// Be careful to use a platform-specific conditional include to only make the
// code visible for the appropriate platform.  Arduino will try to compile and
// link all .cpp files regardless of platform.
#if defined(ARDUINO_ARCH_AVR) || defined(__AVR__)

#include <avr/interrupt.h>
#include <avr/power.h>
#include <avr/sleep.h>
#include <avr/wdt.h>

#include "WatchdogAVR.h"

// Define watchdog timer interrupt.
ISR(WDT_vect) {
  // Nothing needs to be done, however interrupt handler must be defined to
  // prevent a reset.
}

int WatchdogAVR::enable(int maxPeriodMS) {
  // Pick the closest appropriate watchdog timer value.
  int actualMS;
  _setPeriod(maxPeriodMS, _wdto, actualMS);
  // Enable the watchdog and return the actual countdown value.
  wdt_enable(_wdto);
  return actualMS;
}

void WatchdogAVR::reset() {
  // Reset the watchdog.
  wdt_reset();
}

void WatchdogAVR::disable() {
  // Disable the watchdog and clear any saved watchdog timer value.
  wdt_disable();
  _wdto = -1;
}

int WatchdogAVR::sleep(int maxPeriodMS) {
  // Pick the closest appropriate watchdog timer value.
  int sleepWDTO, actualMS;
  _setPeriod(maxPeriodMS, sleepWDTO, actualMS);

  // Build watchdog prescaler register value before timing critical code.
  uint8_t wdps = ((sleepWDTO & 0x08 ? 1 : 0) << WDP3) |
                 ((sleepWDTO & 0x04 ? 1 : 0) << WDP2) |
                 ((sleepWDTO & 0x02 ? 1 : 0) << WDP1) |
                 ((sleepWDTO & 0x01 ? 1 : 0) << WDP0);

  // The next section is timing critical so interrupts are disabled.
  cli();
  // First clear any previous watchdog reset.
  MCUSR &= ~(1 << WDRF);
  // Now change the watchdog prescaler and interrupt enable bit so the
  // watchdog reset only triggers the interrupt (and wakes from deep sleep)
  // and not a full device reset.  This is a timing critical section of
  // code that must happen in 4 cycles.
  WDTCSR |= (1 << WDCE) | (1 << WDE); // Set WDCE and WDE to enable changes.
  WDTCSR = wdps;                      // Set the prescaler bit values.
  WDTCSR |= (1 << WDIE);              // Enable only watchdog interrupts.
  // Critical section finished, re-enable interrupts.
  sei();

  // Disable USB if it exists
#ifdef USBCON
  USBCON |= _BV(FRZCLK); // freeze USB clock
  PLLCSR &= ~_BV(PLLE);  // turn off USB PLL
  USBCON &= ~_BV(USBE);  // disable USB
#endif

  // Set full power-down sleep mode and go to sleep.
  set_sleep_mode(SLEEP_MODE_PWR_DOWN);
  sleep_mode();

  // Chip is now asleep!

  // Once awakened by the watchdog execution resumes here.
  // Start by disabling sleep.
  sleep_disable();

  // Check if user had the watchdog enabled before sleep and re-enable it.
  if (_wdto != -1)
    wdt_enable(_wdto);

  // Return how many actual milliseconds were spent sleeping.
  return actualMS;
}

void WatchdogAVR::_setPeriod(int maxMS, int &wdto, int &actualMS) {
  // Note the order of these if statements from highest to lowest  is
  // important so that control flow cascades down to the right value based
  // on its position in the range of discrete timeouts.
  if ((maxMS >= 8000) || (maxMS == 0)) {
    wdto = WDTO_8S;
    actualMS = 8000;
  } else if (maxMS >= 4000) {
    wdto = WDTO_4S;
    actualMS = 4000;
  } else if (maxMS >= 2000) {
    wdto = WDTO_2S;
    actualMS = 2000;
  } else if (maxMS >= 1000) {
    wdto = WDTO_1S;
    actualMS = 1000;
  } else if (maxMS >= 500) {
    wdto = WDTO_500MS;
    actualMS = 500;
  } else if (maxMS >= 250) {
    wdto = WDTO_250MS;
    actualMS = 250;
  } else if (maxMS >= 120) {
    wdto = WDTO_120MS;
    actualMS = 120;
  } else if (maxMS >= 60) {
    wdto = WDTO_60MS;
    actualMS = 60;
  } else if (maxMS >= 30) {
    wdto = WDTO_30MS;
    actualMS = 30;
  } else {
    wdto = WDTO_15MS;
    actualMS = 15;
  }
}

#endif