/ PPTABLE POUR JSPM du 19-12-2020 par HBE *START_MAJOR_WORDS_WITHOUT_PARAMETERS DELAY , 1010,END , 1,GOHOME , 14,LOCK , 21, OPSTOP , 3,RAPID , 5,RESET , 15,RETRCT , 7, REWIND , 1006,STOP , 2,SWITCH , 6,ULOCK , 20, UNLOAD , 10,ZERO , 13 *END / *START_MAJOR_WORDS_WITH_TEXT COMMENT , 1099,INSERT , 1046,PARTNO , 1045,PPRINT , 1044 *END / *START_MAJOR_WORDS_WITH_PARAMETERS AUXFUN , 1022,BREAK , 1083,CHECK , 1023,CLAMP , 1060, CLEARP , 1004,COOLNT , 1030,COUPLE , 1049,CUTCOM , 1007, CYCLE , 1054,DELAY , 1010,DISPLY , 1021,FEDRAT , 1009, HEAD , 1002,LINTOL , 1073,LOADTL , 1055,MACHIN , 1015, MAXDPM , 1062,MODE , 1003,OPSKIP , 1012,ORIGIN , 1027, PIVOTZ , 1017,PREFUN , 1048,REVERS , 1008,REWIND , 1006, ROTHED , 1035,SAFETY , 1028,SEQNO , 1019,SPINDL , 1031, THREAD , 1036,TOOLNO , 1025,TPRINT , 1075,TRANS , 1037, TURRET , 1033 *END / *START_MINOR_WORDS 3PT2SL , 43,4PT1SL , 44,5PT , 45,AAXIS , 140, ADJUST , 159,ALL , 51,ANGLE , 236,ANTSPI , 176, ARC , 87,AT , 175,ATANGL , 1,AUTO , 88, AVOID , 173,AXIS , 84,BAXIS , 141,BCD , 165, BINARY , 164,BISECT , 230,BLACK , 130,BLUE , 133, BORE , 82,BOREOS , 214,BOTH , 83,BRKCHP , 206, CAM , 169,CAXIS , 142,CBORE , 213,CCLW , 59, CENTER , 2,CHORD , 237,CHUCK , 138,CIRCUL , 75, CIRLIN , 126,CLEARV , 205,CLW , 60,CNSINK , 211, COLLET , 139,COMBIN , 238,CONST , 64,CROSS , 3, CRSSPL , 204,CSINK , 255,CURSEG , 209,CUTANG , 160, DARK , 137,DASH , 124,DECR , 65,DEEP , 153, DEEPHL , 207,DEPTHV , 201,DIAMTR , 203,DITTO , 127, DOTTED , 125,DOWN , 113,DRILL , 163,DWELL , 279, DWELLV , 208,DWL , 253,ENDARC , 58,FACE , 81, FEED , 248,FLOOD , 89,FLOW , 239,FOURPT , 101, FRONT , 148,FULL , 147,FUNOFY , 4,GAPLES , 180, GENCUR , 240,GREEN , 132,HIGH , 62,HOLDER , 157, IN , 48,INCR , 66,INTENS , 134,INTERC , 46, INTGRV , 221,INTOF , 5,INVERS , 6,KEYBOR , 217, LARGE , 7,LAST , 52,LATER , 252,LEFT , 8, LENGTH , 9,LIGHT , 100,LIMIT , 207,LINCIR , 95, LINEAR , 76,LITE , 135,LOCK , 114,LOW , 63, MAIN , 93,MANUAL , 158,MAXRPM , 79,MED , 136, MEDIUM , 61,MILL , 151,MINUS , 10,MIRROR , 56, MIST , 90,MMPM , 171,MMPR , 172,MODIFY , 55, MULTRD , 119,MXMMPM , 177,NEGX , 11,NEGY , 12, NEGZ , 13,NEXT , 162,NIXIE , 99,NOMORE , 53, NORMAL , 111,NOTE , 181,NOW , 161,NOX , 14, NOY , 15,NOZ , 16,OFF , 72,OMIT , 172, ON , 71,OPEN , 50,OPTION , 144,ORIENT , 246, OUT , 49,PARAB , 77,PARAM , 241,PARLEL , 17, PART , 166,PAST , 70,PEN , 128,PERPTO , 18, PERSP , 67,PILOTD , 224,PLUS , 19,PNTVEC , 200, POSX , 20,POSY , 21,POSZ , 22,PTNORM , 104, PTSLOP , 103,PULBOR , 218,PULFAC , 223,QUILL , 287, RADIUS , 23,RAIL , 93,RANDOM , 174,RANGE , 145, REAM , 167,REAMA , 219,REAR , 149,RED , 131, RETAIN , 171,REV , 97,REVOLV , 208,RIGHT , 24, ROTREF , 68,RPM , 78,RTHETA , 106,RULED , 210, SADDLE , 150,SAME , 54,SCALE , 25,SCRIBE , 129, SEG , 242,SETANG , 156,SETOOL , 155,SFM , 115, SIDE , 94,SLOPE , 47,SMALL , 26,SMESH , 243, SOLID , 123,SPDRL , 210,SPECDP , 202,SPEED , 249, SPLINE , 105,SPMIL , 212,START , 57,STEP , 92, TANON , 109,TANTO , 27,TAP , 168,TAPKUL , 91, THETAR , 107,THRU , 152,TIMES , 28,TO , 69, TPMM , 178,TRANSL , 29,TRAV , 154,TRFORM , 110, TRYBOR , 215,TRYBOS , 216,TURN , 80,TWOPT , 102, TYPE , 98,UAXIS , 227,UNIT , 30,UP , 112, VAXIS , 228,WAXIS , 229,WDEFAC , 222,WEIGHT , 206, XAXIS , 84,XCOORD , 116,XLARGE , 31,XSMALL , 32, XYOF , 209,XYPLAN , 33,XYROT , 34,XYVIEW , 120, XYZ , 108,YAXIS , 85,YCOORD , 117,YLARGE , 35, YSMALL , 36,YZPLAN , 37,YZROT , 38,YZVIEW , 121, ZAXIS , 86,ZCOORD , 118,ZIGZAG , 170,ZLARGE , 39, ZSMALL , 40,ZXPLAN , 41,ZXROT , 42,ZXVIEW , 122 *END / *START_SYNTAXES CLAMP/(ON,OFF) COOLNT/(ON,OFF,FLOOD,MIST,THRU,AIR) DELAY/(,REV) MODE/(INCR,ABS) SEQNO/(ON,OFF) SEQNO/START,10,INCR,2 *END / / ********************************************************************************************************* / ******************************* PART OPERATION/PROGRAM DATA ************************************* / ********************************************************************************************************* / *START_NC_INSTRUCTION NC_PROGRAM_HEADER *START_SEQUENCE CHANNEL/%MFG_CHANNEL_NUMBER *END *END / *START_NC_INSTRUCTION NC_START_MACRO *START_SEQUENCE PARTNO/%MFG_PROGRAM_NAME PPTABLE/%MFG_PP_WORD_TBL $$ BASE IMS PPTABLE 06/10/2020 MOD HBE DU 19-12-2020 PART_OPE/%MFG_IDENTIFIER PROGRAM/%MFG_PROGRAM_NAME MACHINE/%MFG_MACHINE_NAME CATPROCESS/%MFG_MODEL_NAME CATPRODUCT/%MFG_PRODUCT_NAME MAXRPM/%MFG_LATHE_MAX_SPNDL_SPEED *END *END / *START_NC_INSTRUCTION NC_END_MACRO *START_SEQUENCE $$ SPINDL/OFF $$ REWIND/0 $$ END/ *END *END / / ********************************************************************************************************* / ************************************ HEAD/TOOL CHANGE ******************************************* / ********************************************************************************************************* / *START_NC_COMMAND NC_HEAD_CHANGE *START_SEQUENCE HEAD/%MFG_HEAD_NAME *END *END / *START_NC_INSTRUCTION NC_TOOL_CHANGE *START_SEQUENCE TPRINT/%MFG_TOOL_NAME TCOM/%MFG_TOOL_COMMENT T_ASSY/%MFG_TL_ASMBLY_ID,%MFG_ASS_COMMENT T_HOLDER/%MFG_HOLDER_NAME,%MFG_HOLDER_COMMENT,%MFG_HOLDER_COMMENT_1,%MFG_HOLDER_COMMENT_2 TDATA/MILL,%MFG_TL_SET_X,%MFG_TL_SET_Y,%MFG_TL_SET_LGTH,DIAM,%MFG_NOMINAL_DIAM,%MFG_ENTRY_DIAM,$ TYPE,%MFG_NAME_BAS,WEIGHT,%MFG_WEIGHT_SNTX,$ ANGLE,%MFG_CUT_ANGLE,PITCH,%MFG_PITCH_OF_THREAD,$ FLUTES,%MFG_NB_OF_FLUTES,TEETH,%MFG_TOOTH_DES,$ CORE,%MFG_TOOL_CORE_DIAMETER,TIP,%MFG_TL_TIP_LGTH,$ MOUNT,%MFG_STATION_MACHINE_NAME LOADTL/%MFG_TOOL_NUMBER,ADJUST,%MFG_TL_COMP,SPINDL,%MFG_SPNDL_MACH,%MFG_TOOL_ASS_POW COOLNT/%MFG_COOLNT_SNTX *END *END / *START_NC_INSTRUCTION NC_TOOL_CHANGE_LATHE *START_SEQUENCE TPRINT/%MFG_TOOL_NAME TCOM/%MFG_TOOL_COMMENT T_ASSY/%MFG_TL_ASMBLY_ID,%MFG_ASS_COMMENT T_HOLDER/%MFG_HOLDER_NAME,%MFG_HOLDER_COMMENT,%MFG_HOLDER_COMMENT_1,%MFG_HOLDER_COMMENT_2 TDATA/TURN,%MFG_TL_SET_X,%MFG_TL_SET_Y,%MFG_TL_SET_Z,QUADRANT,%MFG_QUADRANT,RADIUS,%MFG_NOSE_RADIUS,$ ANGLE,%MFG_TL_SETUP_ANG,INV,%MFG_TOOL_INVERT,$ TYPE,%MFG_NAME_BAS,WEIGHT,%MFG_WEIGHT_SNTX,$ INSERT_L,%MFG_INSERT_LGTH,INSCRIB,%MFG_INSCRIB_DIAM,THREAD_ANGLE,%MFG_THREAD_ANGLE,LF,$ BAR_R,%MFG_BAR_CUT_RAD,BAR_L,%MFG_BAR_LENGTH_1,%MFG_BAR_LENGTH_2,$ MOUNT,%MFG_STATION_NAME LOADTL/%MFG_TOOL_NUMBER,ADJUST,%MFG_TL_COMP,TURN COOLNT/%MFG_COOLNT_SNTX *END *END / / ********************************************************************************************************* / **************************** OPERATION INFORMATION (Start/End) ********************************** / ********************************************************************************************************* / *START_NC_COMMAND NC_3X_MO_TOOLPATH_TYPE *START_LIST MFG_TOOLPATH_TYPE 3AXIS ,5AXIS *END TOOLPATH_TYPE/&MFG_TOOLPATH_TYPE *END / *START_NC_COMMAND NC_5X_MO_TOOLPATH_TYPE TOOLPATH_TYPE/&MFG_TOOLPATH_TYPE *END / *START_NC_COMMAND NC_MILL_MO_TOOLPATH_TYPE TOOLPATH_TYPE/&MFG_TOOLPATH_TYPE *END / /*START_NC_COMMAND NC_AXIAL_MO_TOOLPATH_TYPE / Does not exist --> see NC_AXIAL_MO_START_COMMENT / *START_NC_INSTRUCTION NC_AXIAL_MO_START_COMMENT *START_SEQUENCE OP_NAME/%MFG_MO_IDENTIFIER START_OP/AXIAL OPDATA/TYPE,%MFG_MO_TYPE,PATTERN,%MFG_PATTERN_NAME,$ %MFG_FEED_UNIT,FEED_MACH,%MFG_FEED_MACH,FEED_RTRCT,%MFG_FEED_RETRACT_VALUE,FEED_APP,%MFG_FEED_APP_VALUE,$ FEED_FINISH,%MFG_FEED_FINISH_VALUE,$ DIRCUT,%MFG_DIR_CUT,LF SPINDL_NAME/NAME,%MFG_SPINDLE_NAME,NUMB,%MFG_SPINDLE_NUMBER TOOLPATH_TYPE/AXIAL,&MFG_TOOLPATH_TYPE,%MFG_MO_TOOL_POW *END *END / *START_NC_INSTRUCTION NC_MILL_MO_START_COMMENT *START_SEQUENCE OP_NAME/%MFG_MO_IDENTIFIER START_OP/MILL OPDATA/ACCURACY,%MfgMachiningTolerance,OFFSET,%MfgGlobalOffsetOnContour,%MfgGlobalOffsetOnBottom,$ %MFG_FEED_UNIT,FEED_MACH,%MFG_FEED_MACH,FEED_RTRCT,%MFG_FEED_RETRACT_VALUE,FEED_APP,%MFG_FEED_APP_VALUE,$ FEED_FINISH,%MFG_FEED_FINISH_VALUE,$ DIRCUT,%MFG_DIR_CUT,LF SPINDL_NAME/NAME,%MFG_SPINDLE_NAME,NUMB,%MFG_SPINDLE_NUMBER *END *END / *START_NC_INSTRUCTION NC_3X_MO_START_COMMENT *START_SEQUENCE OP_NAME/%MFG_MO_IDENTIFIER START_OP/3X OPDATA/ACCURACY,%MfgMachiningTolerance,TYPE,%MFG_MO_TYPE,OFFSET,%MfgGlobalOffsetOnContour,%MfgGlobalOffsetOnBottom,$ %MFG_FEED_UNIT,FEED_MACH,%MFG_FEED_MACH,FEED_RTRCT,%MFG_FEED_RETRACT_VALUE,FEED_APP,%MFG_FEED_APP_VALUE,$ FEED_FINISH,%MFG_FEED_FINISH_VALUE,$ DIRCUT,%MFG_DIR_CUT,LF SPINDL_NAME/NAME,%MFG_SPINDLE_NAME,NUMB,%MFG_SPINDLE_NUMBER *END *END / *START_NC_INSTRUCTION NC_5X_MO_START_COMMENT *START_SEQUENCE OP_NAME/%MFG_MO_IDENTIFIER START_OP/5X OPDATA/ACCURACY,%MfgMachiningTolerance,TYPE,%MFG_MO_TYPE,$ %MFG_FEED_UNIT,FEED_MACH,%MFG_FEED_MACH,FEED_RTRCT,%MFG_FEED_RETRACT_VALUE,FEED_APP,%MFG_FEED_APP_VALUE,$ FEED_FINISH,%MFG_FEED_FINISH_VALUE,$ DIRCUT,%MFG_DIR_CUT,LF SPINDL_NAME/NAME,%MFG_SPINDLE_NAME,NUMB,%MFG_SPINDLE_NUMBER *END *END / *START_NC_INSTRUCTION NC_LATHE_MO_START_COMMENT *START_SEQUENCE OP_NAME/%MFG_MO_IDENTIFIER START_OP/LATHE OPDATA/ACCURACY,%MfgMachiningTolerance,TYPE,%MFG_MO_TYPE,$ %MFG_FEED_UNIT,FEED_MACH,%MFG_FEED_MACH,FEED_RTRCT,%MFG_FEED_RETRACT_VALUE,FEED_APP,%MFG_FEED_APP_VALUE,$ FEED_FINISH,%MFG_FEED_FINISH_VALUE SPINDL_NAME/NAME,%MFG_SPINDLE_NAME,NUMB,%MFG_SPINDLE_NUMBER TOOLPATH_TYPE/TURN *END *END / *START_NC_COMMAND NC_SPINDLE_MAXSPEED MAXRPM_OP/%MFG_MAX_SPNDL_SPEED,&MFG_MAX_SPNDL_UNIT,&MFG_SPNDL_WAY *END / *START_NC_INSTRUCTION NC_AXIAL_MO_END_COMMENT *START_SEQUENCE END_OP/AXIAL *END *END / *START_NC_INSTRUCTION NC_MILL_MO_END_COMMENT *START_SEQUENCE END_OP/MILL *END *END / *START_NC_INSTRUCTION NC_3X_MO_END_COMMENT *START_SEQUENCE END_OP/3X *END *END / *START_NC_INSTRUCTION NC_5X_MO_END_COMMENT *START_SEQUENCE END_OP/5X *END *END / *START_NC_INSTRUCTION NC_LATHE_MO_END_COMMENT *START_SEQUENCE END_OP/LATHE *END *END / / ************************************************************************************************** / ************************** TOOL COMPENSATION (Length/Radius) ***************************** / ************************************************************************************************** / *START_NC_COMMAND NC_COMPENSATION TLCOMP/%MFG_TL_NUMBER,ADJUST,%MFG_TL_COMP *END / *START_NC_COMMAND NC_CHANGE_REF_PT SWITCH/%MFG_QUADRANT,%MFG_TL_COMP *END / *START_NC_COMMAND NC_CUTCOM_ON CUTCOM/ON *END / *START_NC_COMMAND NC_CUTCOM_OFF CUTCOM/OFF *END / *START_NC_COMMAND NC_CUTCOM_LEFT CUTCOM/LEFT,%MFG_TL_COMP_RAD *END / *START_NC_COMMAND NC_CUTCOM_RIGHT CUTCOM/RIGHT,%MFG_TL_COMP_RAD *END / / ********************************************************************************************************* / ************************************* OTHER ACTIVITIES ****************************************** / ********************************************************************************************************* / *START_NC_COMMAND NC_COMMENT %MFG_MO_COMMENT *END / *START_NC_INSTRUCTION NC_MACHINING_AXIS *START_SEQUENCE $$ %MFG_NCAXIS_IDENTIFIER $$ %MFG_NCAXIS_X_VECX_REFPO %MFG_NCAXIS_X_VECY_REFPO %MFG_NCAXIS_X_VECZ_REFPO %MFG_NCAXIS_X_ORIG_REFPO $$ %MFG_NCAXIS_Y_VECX_REFPO %MFG_NCAXIS_Y_VECY_REFPO %MFG_NCAXIS_Y_VECZ_REFPO %MFG_NCAXIS_Y_ORIG_REFPO $$ %MFG_NCAXIS_Z_VECX_REFPO %MFG_NCAXIS_Z_VECY_REFPO %MFG_NCAXIS_Z_VECZ_REFPO %MFG_NCAXIS_Z_ORIG_REFPO CATMAT/%MFG_NCAXIS_X_ORIG_REFPO,%MFG_NCAXIS_Y_ORIG_REFPO,%MFG_NCAXIS_Z_ORIG_REFPO,%MFG_NCAXIS_X_VECX_REFPO,%MFG_NCAXIS_X_VECY_REFPO,%MFG_NCAXIS_X_VECZ_REFPO,%MFG_NCAXIS_Y_VECX_REFPO,%MFG_NCAXIS_Y_VECY_REFPO,%MFG_NCAXIS_Y_VECZ_REFPO,%MFG_NCAXIS_Z_VECX_REFPO,%MFG_NCAXIS_Z_VECY_REFPO,%MFG_NCAXIS_Z_VECZ_REFPO,%MFG_NCAXIS_IDENTIFIER *END *END / *START_NC_INSTRUCTION NC_ORIGIN *START_SEQUENCE ORGNUM/NUMB,%MFG_ORIGIN_NUMBER,GROUP,%MFG_ORIGIN_GROUP *END *END / *START_NC_COMMAND NC_FEEDRATE *START_LIST MFG_FEED_UNIT MMPM ,MMPR *END FEDRAT/%MFG_FEED_VALUE,&MFG_FEED_UNIT,&MFG_FEED_TYPE *END / *START_NC_COMMAND NC_SPINDLE SPINDL/%MFG_SPNDL_SPEED,&MFG_SPNDL_UNIT,&MFG_SPNDL_WAY *END / *START_NC_COMMAND NC_SPINDLE_START *START_LIST MFG_SPNDL_UNIT RPM ,SFM *END SPINDL/%MFG_SPNDL_SPEED,&MFG_SPNDL_UNIT,&MFG_SPNDL_WAY *END / *START_NC_COMMAND NC_SPINDLE_LATHE *START_LIST MFG_SPNDL_UNIT RPM ,SFM *END SPINDL/%MFG_SPNDL_SPEED,&MFG_SPNDL_UNIT,&MFG_SPNDL_WAY *END / *START_NC_COMMAND NC_SPINDLE_ON SPINDL/ON *END / *START_NC_COMMAND NC_SPINDLE_OFF SPINDL/OFF *END / *START_NC_COMMAND NC_SPINDLE_STOP SPINDL/&MFG_SPNDL_STOP *END / *START_NC_COMMAND NC_SPINDLE_LOCK SPINDL/LOCK *END / *START_NC_COMMAND NC_HELICAL_INTERPOLATION *START_SEQUENCE HELICAL/CENTER,%MFG_HELICAL_X_CENTER,%MFG_HELICAL_Y_CENTER,%MFG_HELICAL_Z_CENTER,INDIRV,%MFG_HELICAL_INDIRV_I,%MFG_HELICAL_INDIRV_J,%MFG_HELICAL_INDIRV_K,$ AXIS,%MFG_HELICAL_I_AXIS,%MFG_HELICAL_J_AXIS,%MFG_HELICAL_K_AXIS,$ PITCH,%MFG_HELICAL_PITCH,RADIUS,%MFG_HELICAL_RADIUS,ANGLE,%MFG_HELICAL_ANGLE,HEIGHT,%MFG_HELICAL_HEIGHT,ROUND,%MFG_HELICAL_ROUND,$ END,%MFG_HELICAL_X_END,%MFG_HELICAL_Y_END,%MFG_HELICAL_Z_END *END *END / *START_NC_COMMAND NC_DELAY *START_LIST MFG_DELAY_UNIT REV ,SEC *END DELAY/%MFG_DELAY_VALUE,&MFG_DELAY_UNIT *END / *START_NC_COMMAND NC_SYNCHRONISATION SYNC/%MFG_SYNCHRONISATION_NUMBER,%MFG_CHANNEL1,%MFG_CHANNEL2,%MFG_MASTER_CHANNEL *END / *START_NC_COMMAND NC_MULTAX_ON MULTAX/ON *END / *START_NC_COMMAND NC_MULTAX_OFF MULTAX/OFF *END / / ********************************************************************************************************* / *********************************** DRILLING CYCLES ******************************************* / ********************************************************************************************************* / *START_NC_INSTRUCTION NC_DRILLING *START_SEQUENCE CYCLE/DRILL,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE *END *END / *START_NC_INSTRUCTION NC_SPOT_DRILLING *START_SEQUENCE CYCLE/DRILL,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE *END *END / *START_NC_INSTRUCTION NC_DRILLING_DWELL_DELAY *START_SEQUENCE CYCLE/FACE,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE *END *END / *START_NC_INSTRUCTION NC_DEEPHOLE *START_SEQUENCE CYCLE/DEEP,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ INCR,%MFG_AXIAL_DEPTH,%MFG_DEPTH_DEC,%MFG_DEPTH_LIM,INCRD,%MFG_OFFSET_RET *END *END / *START_NC_INSTRUCTION NC_BREAK_CHIPS *START_SEQUENCE CYCLE/BRKCHP,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ INCR,%MFG_AXIAL_DEPTH,INCRD,%MFG_OFFSET_RET *END *END / *START_NC_INSTRUCTION NC_TAPPING *START_SEQUENCE CYCLE/TAP,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ THRD_DIA,%MFG_THREAD_DIAMETER,TL_PITCH,%MFG_TOOL_PITCH,PITCH,%MFG_PITCH *END *END / *START_NC_INSTRUCTION NC_REVERSE_THREADING *START_SEQUENCE CYCLE/LHTAP,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ THRD_DIA,%MFG_THREAD_DIAMETER,TL_PITCH,%MFG_TOOL_PITCH,PITCH,%MFG_PITCH *END *END / *START_NC_INSTRUCTION NC_THREAD_WITHOUT_TAP_HEAD *START_SEQUENCE CYCLE/THREAD,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ DIAMTR,%MFG_DIAMETER,THRD_DIA,%MFG_THREAD_DIAMETER,TL_PITCH,%MFG_TOOL_PITCH,PITCH,%MFG_PITCH *END *END / *START_NC_INSTRUCTION NC_BORING *START_SEQUENCE CYCLE/BORE,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE *END *END / *START_NC_INSTRUCTION NC_BORING_AND_CHAMFERING *START_SEQUENCE CYCLE/FACE,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE *END *END / *START_NC_INSTRUCTION NC_BORING_SPINDLE_STOP *START_SEQUENCE CYCLE/STPBOR,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ LIFTMODE,%MFG_LIFT_MODE,LIFT_X,%MFG_XOFF,LIFT_Y,%MFG_YOFF,LIFT_Z,%MFG_ZOFF,LIFTANGL,%MFG_LIFT_ANGLE,LIFTDIST,%MFG_LIFT_DIST *END *END / *START_NC_INSTRUCTION NC_REAMING *START_SEQUENCE CYCLE/REAM,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE *END *END / *START_NC_INSTRUCTION NC_COUNTERBORING *START_SEQUENCE CYCLE/FACE,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE *END *END / *START_NC_INSTRUCTION NC_COUNTERSINKING *START_SEQUENCE CYCLE/CSINK,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE *END *END / *START_NC_INSTRUCTION NC_TWO_SIDES_CHAMFERING *START_SEQUENCE CYCLE/2S_CHAMF,%MFG_TOTAL_DEPTH,&MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE *END *END / *START_NC_INSTRUCTION NC_BACK_BORING *START_SEQUENCE CYCLE/BAKBOR,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ DIAMTR,%MFG_DIAMETER,RAPTO_BAK,%MFG_CLEAR_TIP_2,DELTA_TIP_TOOL,%MFG_TOOL_COMP_DIST,%MFG_TOOL_COMP_DIST_1,DPTH,%MFG_BCK_BORE_VAL,$ LIFTMODE,%MFG_LIFT_MODE,LIFT_X,%MFG_XOFF,LIFT_Y,%MFG_YOFF,LIFT_Z,%MFG_ZOFF,LIFTANGL,%MFG_LIFT_ANGLE,LIFTDIST,%MFG_LIFT_DIST,$ DEPTH_MAT,%MFG_DETAIL_DEPTH *END *END / *START_NC_INSTRUCTION NC_T_SLOTTING *START_SEQUENCE CYCLE/TSLOT,%MFG_TOTAL_DEPTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,DWELL,%MFG_DELAY_VALUE,DWMODE,%MFG_DWELL_MODE,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ DIAMTR,%MFG_DIAMETER *END *END / *START_NC_INSTRUCTION NC_CIRCULAR_MILLING *START_SEQUENCE CYCLE/CIRCMILL,%MFG_TOTAL_DEPTH,&MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ DIAMTR,%MFG_DIAMETER,CIRCMOD,%MFG_CIRCULAR_MODE,STEP,%MFG_RADIAL_STEP,NPATH,%MFG_RADIAL_NB,INCR,%MFG_AXIAL_DEPTH,PITCH,%MFG_PITCH,DIRCUT,%MFG_DIR_CUT,$ SPRING,%MFG_SPR_PATH,SEQ,%MFG_SEQUENCING_STRAT,DRAFT,%MFG_AUTODRAFTANGLE *END *END / *START_NC_INSTRUCTION NC_THREAD_MILLING *START_SEQUENCE CYCLE/THRDMILL,%MFG_DETAIL_DEPTH,&MFG_FEED_UNIT,%MFG_FEED_MACH,RAPTO,%MFG_CLEAR_TIP,RTRCTO,%MFG_JUMP_DIST,$ FEED_RTRCT,%MFG_FEED_RETRACT,%MFG_FEED_RETRACT_MODE,FEED_APP,%MFG_FEED_APPRCH,%MFG_FEED_APP_MODE,$ TRANSITION,%MFG_FEED_TYPE_TRANSITION,%MFG_LOCAL_FEED_TRANSITION,$ PLUNGE,&MFG_PLUNGE_MODE,&MFG_PLUNGE_TIP,&MFG_PLUNGE_DIAMETER,&MFG_PLUNGE_OFFST,FEED_PLUNGE,%MFG_FEED_PLUNGE_VALUE,&MFG_FEED_PLUNGE_MODE,$ DIAMTR,%MFG_DIAMETER,THRD_DIA,%MFG_THREAD_DIAMETER,PITCH,%MFG_PITCH,%MFG_PITCH_SENS,$ STEP,%MFG_RADIAL_STEP,NPATH,%MFG_RADIAL_NB,THREAD_TYPE,%MFG_THREAD_TYPE,DIR,%MFG_THREAD_DIRECTION,$ STRATEGY,%MFG_THREAD_DIRECTION,%MFG_THREAD_STRATEGY,STEP,%MFG_RADIAL_STEP,NPATH,%MFG_RADIAL_NB,$ SPRING,%MFG_SPR_PATH *END *END / *START_NC_INSTRUCTION NC_LATHE_THREADING *START_SEQUENCE CYCLE/LATHTHRD,%MFG_THREAD_PITCH,%MFG_FEED_UNIT,%MFG_FEED_MACH,NOM_DIAM,%MFG_NOM_DIAM,ORIENTATION,%MFG_THREAD_ORIENTATION,$ PENETRATION,%MFG_THREAD_PENETRATION,PROFILE,%MFG_THREAD_PROFILE,NB_THREADS,%MFG_NUM_THREADS,NB_PATHES,%MFG_NB_PATH,ANGLE,%MFG_ENTER_ANG,$ LENGTH,%MFG_THRD_LENGTH,DEPTH,%MFG_THREAD_DEPTH,LIFT_OFF,%MFG_LIFT_OFF_ANG,%MFG_LIFT_OFF_DIS,COORD,%MFG_END_THRD_RAD,%MFG_END_THRD_AX,THRD_ANG,%MFG_THRD_ANG,$ FIRST_PASSES,%MFG_FIR_PATH,%MFG_NUM_FIR_PATH,LAST_PASSES,%MFG_LAS_PATH,%MFG_NUM_LAS_PATH,%MFG_LAS_DEPT_CUT,SPRING_PASSES,%MFG_SPR_PATH,%MFG_NUM_SPR_PATH,$ START_THRD_RAD,%MFG_ST_THRD_RAD,END_THRD_RAD,%MFG_END_THRD_RAD,LEAD_IN_DIST,%MFG_LEAD_IN_DIST,DEPTH_CUT,%MFG_DEPTH_CUT,MACHINING_TYPE,%MFG_THREAD_MACHINING *END *END / / ********************************************************************************************************* / ************************************ ALL ABOUT PROBING ******************************************* / ********************************************************************************************************* / *START_NC_INSTRUCTION NC_PROBING_SLOT *START_SEQUENCE PROBE/SLOT,%MFG_PROBING_SLOT_WIDTH,%MFG_FEED_UNIT,%MFG_FEED_MACH,OFFSET,%MFG_OFFSET_ON_PART,$ DIST,%MFG_PROBING_SAFETY_DST,%MFG_PROBING_SECURITY_DST,DEPTH,%MFG_PROBING_DEPTH,$ CONTACT,%MFG_PROBING_CONTACT_DEPTH,TOL,%MFG_PROBING_TOLERANCE,$ EXTERN,%MFG_PROBING_SIDE_MODE,TOPPL,%MFG_PROBING_RETURN_BY_TOP_PLANE,DIR,%MFG_PROBING_DIRECTION_X,%MFG_PROBING_DIRECTION_Y,%MFG_PROBING_DIRECTION_Z,$ USER_START,TYPE,%TYPE,ACTION,%ACTION,INFO,%INFO,PARAM,%PARAM,END_PARAM,$ SPROG,%SPROG,VAR_IND,%VAR_IND,VAR_VAL,%VAR_VAL,USER_END *END *END / *START_NC_INSTRUCTION NC_PROBING_HOLE *START_SEQUENCE PROBE/HOLE,%MFG_PROBING_HOLE_DIAMETER,%MFG_FEED_UNIT,%MFG_FEED_MACH,OFFSET,%MFG_OFFSET_ON_PART,$ DIST,%MFG_PROBING_SAFETY_DST,%MFG_PROBING_SECURITY_DST,DEPTH,%MFG_PROBING_DEPTH,$ CONTACT,%MFG_PROBING_CONTACT_DEPTH,TOL,%MFG_PROBING_TOLERANCE,$ EXTERN,%MFG_PROBING_SIDE_MODE,TOPPL,%MFG_PROBING_RETURN_BY_TOP_PLANE,BYCENTER,%MFG_PROBING_RETURN_BY_MIDLE,POINTS,%MFG_PROBING_NB_PROB,$ START,%MFG_PROBING_DIRECTION_X,%MFG_PROBING_DIRECTION_Y,%MFG_PROBING_DIRECTION_Z,ANGLE,%MFG_PROBING_HOLE_ANGLE,$ USER_START,TYPE,%TYPE,ACTION,%ACTION,INFO,%INFO,PARAM,%PARAM,END_PARAM,$ SPROG,%SPROG,VAR_IND,%VAR_IND,VAR_VAL,%VAR_VAL,USER_END *END *END / *START_NC_INSTRUCTION NC_PROBING_CORNER *START_SEQUENCE PROBE/CORNER,&MFG_FEED_UNIT,%MFG_FEED_MACH,OFFSET,%MFG_OFFSET_ON_PART,$ DIST,%MFG_PROBING_SAFETY_DST,%MFG_PROBING_SECURITY_DST,DEPTH,%MFG_PROBING_DEPTH,$ CONTACT,%MFG_PROBING_CONTACT_DEPTH,TOL,%MFG_PROBING_TOLERANCE,$ EXTERN,%MFG_PROBING_SIDE_MODE,OFFSET_PT,%MFG_PROBING_PROB_OFFSET,%MFG_PROBING_PROB_DST,$ FACE1,%MFG_PROBING_DIRECTION_FACE1_X,%MFG_PROBING_DIRECTION_FACE1_Y,%MFG_PROBING_DIRECTION_FACE1_Z,FACE2,%MFG_PROBING_DIRECTION_FACE2_X,%MFG_PROBING_DIRECTION_FACE2_Y,%MFG_PROBING_DIRECTION_FACE2_Z,$ USER_START,TYPE,%TYPE,ACTION,%ACTION,INFO,%INFO,PARAM,%PARAM,END_PARAM,$ SPROG,%SPROG,VAR_IND,%VAR_IND,VAR_VAL,%VAR_VAL,USER_END *END *END / *START_NC_INSTRUCTION NC_PROBING_MULTIPOINTS *START_SEQUENCE PROBE/POINTS,&MFG_FEED_UNIT,%MFG_FEED_MACH,OFFSET,%MFG_OFFSET_ON_PART,$ DIST,%MFG_PROBING_SAFETY_DST,%MFG_PROBING_SECURITY_DST,$ CONTACT,%MFG_PROBING_CONTACT_DEPTH,TOL,%MFG_PROBING_TOLERANCE,$ USER_START,TYPE,%TYPE,ACTION,%ACTION,INFO,%INFO,PARAM,%PARAM,END_PARAM,$ SPROG,%SPROG,VAR_IND,%VAR_IND,VAR_VAL,%VAR_VAL,USER_END $$ Other parameters : %MFG_PROBING_DIRECTION_X,%MFG_PROBING_DIRECTION_Y,%MFG_PROBING_DIRECTION_Z *END *END / *START_NC_INSTRUCTION NC_PROBING_CYCLE_OFF *START_SEQUENCE PROBE/OFF *END *END / *START_NC_INSTRUCTION NC_PROBING_MO_START_COMMENT *START_SEQUENCE OP_NAME/%MFG_MO_IDENTIFIER START_OP/PROBING OPDATA/%MFG_FEED_UNIT,FEED_MACH,%MFG_FEED_MACH,FEED_RTRCT,%MFG_FEED_RETRACT_VALUE,FEED_APP,%MFG_FEED_APP_VALUE,$ FEED_FINISH,%MFG_FEED_FINISH_VALUE SPINDL_NAME/NAME,%MFG_SPINDLE_NAME,NUMB,%MFG_SPINDLE_NUMBER *END *END / *START_NC_COMMAND NC_PROBING_MO_TOOLPATH_TYPE TOOLPATH_TYPE/PROBE,&MFG_TOOLPATH_TYPE *END / *START_NC_INSTRUCTION NC_PROBING_MO_END_COMMENT *START_SEQUENCE END_OP/PROBING *END *END / /********************************************************************************** /**************** Machine Instruction / Rotation **************** /********************************************************************************** / *START_NC_INSTRUCTION NC_HEAD_ROTATION *START_SEQUENCE ROTHED/%MFG_AMOUNT_ROT,%MFG_DIR_OF_ROT,%MFG_ABC_AXIS *END *END / *START_NC_INSTRUCTION NC_TABLE_ROTATION *START_SEQUENCE ROTABL/%MFG_AMOUNT_ROT,%MFG_DIR_OF_ROT,%MFG_ABC_AXIS *END *END / *START_NC_INSTRUCTION NC_AXIS_LOCK *START_SEQUENCE LOCK/%MFG_NCAXIS_NAME,%MFG_AXIS_LOCK_STATUS *END *END / *START_NC_INSTRUCTION NC_AXIS_MOVE *START_SEQUENCE MOVE/%MFG_NCAXIS_NAME,%MFG_AXIS_POSITION *END *END / *START_NC_COMMAND NC_MILL_TURRET_ORIENTATION *START_SEQUENCE BAXIS/%MFG_MILL_TURRET_I_AXIS,%MFG_MILL_TURRET_J_AXIS,%MFG_MILL_TURRET_K_AXIS *END *END / / ********************************************************************************************************* / ************************************ PART SEQUENCING ******************************************* / ********************************************************************************************************* / *START_NC_COMMAND NC_PART_SEQUENCING_START START_OP/PART_SEQUENCING *END / *START_NC_COMMAND NC_PART_SEQUENCING_END END_OP/PART_SEQUENCING *END / *START_NC_COMMAND NC_PART_SEQ_AXIS_MOVE MOVE/%MFG_AXIS_NAME,%MFG_AXIS_POSITION *END / *START_NC_COMMAND NC_PART_SEQ_FEEDRATE *START_LIST MFG_PART_FEED_UNIT MMPM ,MMPR *END PART_FEDRAT/%MFG_PART_FEED_VALUE,&MFG_PART_FEED_UNIT *END / *START_NC_COMMAND NC_PART_SEQUENCING_DWELL DELAY/%MFG_DELAY_VALUE *END /